How to Clean and Store a Sucking Masturbator Toy

By Adult Sex Toys - Online Store | Published: 2026-11-04

Category: Tips & Care

A practical, step-by-step routine for cleaning, drying, and storing a sucking masturbator so the sleeve stays hygienic and the motor keeps working.

Quick answer

Clean your sucking masturbator immediately after each use with warm water and a mild toy cleaner, rinse the sleeve thoroughly, and let every part air-dry completely before reassembling or storing it. Keep the motor and battery compartment dry, and store the toy in a cool, dust-free place away from direct sunlight.

Why the motor changes the cleaning routine

A sucking masturbator is not just a sleeve; it has a motor, suction mechanism, and often a rechargeable battery. Water in the wrong place can damage the electronics or create a hygiene problem you cannot see. That is why you clean the sleeve separately from the outer case whenever the design allows, and why you never submerge the motorized portion.

The material also matters. Many sleeves, including the one in The Milker Intense 13X Sucking Masturbator, are made of TPE, which is soft and porous. TPE needs thorough rinsing and complete drying because moisture trapped in the material encourages bacteria and can break down the surface over time. Silicone sleeves are less porous, but the same drying rule applies.

The drying mistake most people make

Putting the toy back together while the sleeve is still damp is the most common cause of odor, mildew, and sticky residue. Air-drying on a clean towel in a well-ventilated room is safer than using a hair dryer, because heat can warp TPE and damage the motor housing. If you are in a hurry, pat the outside dry with a lint-free cloth and leave the sleeve open to finish drying.

Never store a masturbator in a sealed bag or drawer while it is damp. Trapped moisture is the enemy of both the material and the motor.

Step-by-step cleaning and storage routine

Disassemble what you can: Separate the sleeve from the outer case and remove any removable parts, such as the cap or battery cover. Check the manufacturer's instructions for your model first. Common mistake: forcing parts apart that are not designed to be removed, which can tear the sleeve or crack the case. If a part does not come off with gentle pressure, leave it attached and clean around it.
Rinse the sleeve with warm water: Rinse the sleeve inside and out with warm, not hot, water to remove residue. Avoid getting water into the motor or suction openings on the case. Common mistake: using hot water, which can degrade TPE and make it tacky. Keep the motorized case out of the sink and rinse only the sleeve.
Wash with mild toy cleaner: Apply a small amount of mild toy cleaner or unscented soap to the sleeve and gently work it into the nubs and ridges with your fingers or a soft cloth. Do not use household cleaners, alcohol, or abrasive sponges. Common mistake: scrubbing hard, which can tear the soft TPE. Use only cleaners labeled safe for TPE or silicone toys.
Rinse thoroughly: Rinse the sleeve until the water runs clear and no slippery residue remains. Soap left behind can irritate skin and attract dust. Common mistake: stopping too soon because the surface feels smooth. Feel the sleeve after rinsing; it should not feel slick or soapy.
Shake out excess water: Shake the sleeve gently over the sink to remove standing water, then pat the outside dry with a clean, lint-free towel. Do not wring or twist the sleeve. Common mistake: wringing it like a washcloth, which stresses the material. Pat, do not twist.
Air-dry completely: Place the sleeve on a clean, dry towel in a well-ventilated area, open side up, and let it air-dry fully. Turn it occasionally so air reaches all surfaces. Common mistake: putting it away while the inside still feels cool or damp. Allow several hours; if in doubt, leave it longer.
Wipe the outer case: Wipe the outer case and motor housing with a slightly damp cloth and mild cleaner, then dry immediately with a soft towel. Never rinse the case under running water. Common mistake: letting water seep into seams or buttons. The case should never be submerged.

Product note

The Milker Intense 13X Sucking Masturbator: The Milker Intense 13X Sucking Masturbator has a nubbed interior sleeve made of phthalate-free TPE and an outer case of TPE and ABS plastic, with 3 intense suction modes. Because the sleeve is TPE and the case houses the suction mechanism, you should remove and clean the sleeve separately and keep the outer case dry to protect the motor.
The Milker Intense 13X Sucking Masturbator